

Product Specifications
- Brand
- Nordson Corporation
- Part Number
- Encore®
- Product Type
- Digital Powder Coating Control System
- Configurations
- 4-gun, 6-gun, or 8-gun modular cabinet
- Electrostatic Output
- 100 kV max, 100 µA max
- Charge Modes
- Select Charge (3 presets: recoating, metallics, deep recesses) + Custom (independent kV/µA) + AFC (Automatic Feedback Current)
- Pneumatic Modes
- Classic Flow (independent flow + atomizing air) and Smart Flow (auto-adjusted atomizing based on flow %)
- Min. Inlet Air Pressure
- 60 psi (4.1 bar) for full repeatability
- Conventional Pump Output
- Up to 750 g/min (Venturi)
- HDLV Pump Output
- Up to 4 kg/min (dense-phase), ~20-second colour change
- Interface
- Digital push-button per gun controller; master panel with all-guns trigger
- Gun Compatibility
- Encore bar-mount and tube-mount automatic spray guns, air-purge cleanable
Product Description
The Encore system is Nordson's all-digital platform for automatic powder coating lines — replacing the analog pneumatic regulators, mechanical pressure gauges, and manual kV potentiometers of previous-generation equipment with digitally controlled electro-pneumatics. Each gun channel receives digital setpoints for flow air, atomizing air, electrostatic voltage, and current limit; the controller maintains these values through closed-loop feedback, eliminating the drift that mechanical regulators experience as supply pressure fluctuates, temperature changes, or regulator springs age. The system achieves full repeatability at incoming air pressures as low as 60 psi (4.1 bar) — important for plants at the end of long compressed air distribution runs where pressure drop is a daily reality.
How does Smart Flow differ from Classic Flow pneumatic control?
In Classic Flow mode, the operator sets the flow air (which transports powder from the pump to the gun) and atomizing air (which shapes the powder cloud at the gun tip) independently — two separate setpoints. In Smart Flow mode, the operator sets only the total powder output as a percentage; the controller automatically adjusts atomizing air proportionally based on the flow air setting, maintaining a consistent powder cloud shape across the full output range. This is particularly useful when the powder flow rate varies during a part program — for example, high flow on large flat surfaces and reduced flow on complex geometries — because it prevents the cloud from becoming too dilute at low flow (over-atomized, poor transfer efficiency) or too dense at high flow (under-atomized, orange peel finish).
What is Automatic Feedback Current (AFC) and when is it used?
In standard electrostatic mode, the operator sets a fixed kV output — say 80 kV. As the gun moves closer to the part, the current (µA) increases because the electrical resistance between the gun electrode and the grounded part decreases. At very close distances, this can cause back-ionization — a phenomenon where excessive current through the powder layer creates micro-arcing that produces pinholes, orange peel, and uneven film thickness. AFC mode instead lets the operator set a target current limit; the controller continuously adjusts the kV up or down to maintain that current regardless of gun-to-part distance. When the gun approaches a deep recess — where distance is larger and the electric field weaker — the controller increases kV to maintain wrap-around. When the gun moves close to a flat surface — where distance is small — it reduces kV to prevent back-ionization. The result is consistent film build across complex geometries without manual gun-to-part distance management.
What changed from the original Encore to Encore HD / HDLV?
The Encore HD variant replaces the Venturi pump — which uses a high-velocity air jet through a throat to create suction that draws powder from the hopper — with a dense-phase HDLV (High-Density Low-Velocity) pump. The HDLV pump is pneumatically operated with no Venturi throat, pistons, or diaphragms to wear; the pinch-valve tube is the main wear item. Key differences: powder output increases from 750 g/min to 4 kg/min; powder exit velocity is approximately 4× slower, producing a softer, more thoroughly charged powder cloud that wraps better around complex shapes; and the colour change time drops to approximately 20 seconds with fully automatic purging — no disassembly required. The HDLV pump can also transport powder over longer distances and greater vertical lifts than the Venturi, enabling centralized powder supply rooms serving multiple booths.
Resources & Documentation
Nordson Encore | All-Digital Modular Powder Coating Control System, 100 kV, 4-8 Guns
Product Specifications
- Brand
- Nordson Corporation
- Part Number
- Encore®
- Product Type
- Digital Powder Coating Control System
- Configurations
- 4-gun, 6-gun, or 8-gun modular cabinet
- Electrostatic Output
- 100 kV max, 100 µA max
- Charge Modes
- Select Charge (3 presets: recoating, metallics, deep recesses) + Custom (independent kV/µA) + AFC (Automatic Feedback Current)
- Pneumatic Modes
- Classic Flow (independent flow + atomizing air) and Smart Flow (auto-adjusted atomizing based on flow %)
- Min. Inlet Air Pressure
- 60 psi (4.1 bar) for full repeatability
- Conventional Pump Output
- Up to 750 g/min (Venturi)
- HDLV Pump Output
- Up to 4 kg/min (dense-phase), ~20-second colour change
- Interface
- Digital push-button per gun controller; master panel with all-guns trigger
- Gun Compatibility
- Encore bar-mount and tube-mount automatic spray guns, air-purge cleanable