12 month warranty Request a Quote Technical Support
Sign In

Product Specifications

Product Description

OptiBond is Nordson's brand for closed-loop hot-melt adhesive flow control — a methodology shift from the traditional open-loop approach of "set the pump speed and hope the add-on weight stays constant." In open-loop systems, adhesive viscosity changes with temperature fluctuation, batch variation, and char formation in the melter cause the same pump speed to deliver different actual flow rates. The operator compensates by periodically weighing samples and manually adjusting, but between checks, product can be running with insufficient or excessive adhesive — the former causing bond failure and returns, the latter wasting material. OptiBond closes this loop by measuring actual flow and correcting in real time.

How does TruFlow closed-loop control work in practice?

A TruFlow positive-displacement flow meter is installed downstream of the melt pump — in the hot-melt supply line, at the distributor, or at the applicator head depending on the system architecture. As adhesive flows through the meter, it rotates a precision gear set; each rotation displaces a known volume, and the rotation frequency encodes the volumetric flow rate. The Concert flow controller reads this actual flow, compares it to the target flow (derived from the machine's line speed and the desired add-on weight in g/m²), and adjusts the melt pump speed or the flow control valve to eliminate any deviation. Because positive-displacement metering is independent of adhesive viscosity, temperature, and density within the meter's design range, the measurement remains accurate even as the adhesive degrades or the melter temperature fluctuates — conditions that would cause a pressure-based flow estimate to drift.

What is the difference between passive and active metering in the OptiBond architecture?

Approach Metering Location Control Method Best For
Passive (TruFlow applicator) At the applicator head — gear driven by material flow All modules receive consistent add-on weight; flow control at the melter Consistent-width patterns, fewer applicator positions
Active (Universal Slice applicator) At the applicator head — motor and drive per module Each module independently controlled for individual add-on weight Complex products with multiple different patterns, widths, and coat weights
Intermediate (TruFlow distributor) At the hose split point Single meter per hose branch, individual control per stream Splitting one melter output to multiple independent lanes

Frequently Asked Questions

Can OptiBond be retrofitted to older Nordson melters?

The Concert series flow controllers are designed as standalone units that can be added to existing melters, provided the melter has an available pump speed control interface (analog 0–10 V or communication bus). The TruFlow flow meter is installed in the existing hose or manifold, and the Concert controller takes over pump speed regulation. For the oldest melters without electronic pump control, retrofitting may require a pump drive upgrade — contact Nordson for a machine-specific assessment.

Does closed-loop control eliminate the need for periodic add-on weight checks?

OptiBond dramatically reduces add-on weight variation from the ±15–25% typical of open-loop systems to approximately ±2–5%, but periodic gravimetric checks — weighing a known area of coated substrate — remain recommended as a calibration verification, particularly after product changeovers, melter maintenance, or raw material lot changes. The system provides continuous measurement and control between checks, but the flow meter itself should be verified against a gravimetric reference periodically to detect any mechanical wear or calibration drift over thousands of operating hours.

Resources & Documentation

Nordson
Compare

Nordson OptiBond | Closed-Loop Adhesive Flow Control System for Nonwovens Manufacturing

Closed-Loop Adhesive Flow Control System
MPN/Series: OptiBond™

Product Specifications

Brand
Nordson Corporation
Part Number
OptiBond™
Product Type
Closed-Loop Adhesive Flow Control System
Control Methodology
Closed-loop — measures actual flow, compares to setpoint, adjusts pump speed in real time
Core Components
TruFlow positive-displacement flow meters, TruFlow distributors (up to 8 streams), Concert flow controllers, VersaBlue Plus / AltaBlue Touch melters
Interface
Optix colour touchscreen with real-time status, data logging, and graphical analysis
Flow Controller
Concert series — monitors or controls up to 2 dispensing loops, supports 3 heated zones
Application
Nonwovens and disposable hygiene manufacturing (diapers, feminine care, adult incontinence)
Key Benefit
Eliminates add-on weight drift caused by viscosity, temperature, and line speed variations

Resources & Documentation

Nordson OptiBond | Closed-Loop Adhesive Flow Control System for Nonwovens Manufacturing
×