
Product Specifications
- Manufacturer
- Dimac Srl
- Model
- SPC-360
- Product Type
- Robotic in-process SPC inspection unit
- Working Range
- Parts from 3 to 20 mm, as delivered on a complex-geometry cold-forging job
- Loading
- Two sliding drawers, 36 backlit slots each
- Handling
- Cobot with head-mounted camera and two linear axes
- Cameras
- Up to 4: cobot head, horizontal, upper and diagonal, plus an encoder rotary table
- Faces Inspected
- Six outer faces and, on many parts, the inner faces of the broach
- Repeatability
- Standard deviation below 1 micron on backlit profile images; about twice that on grey-tone images
- Measurements
- Up to 50 different measurements per part number
- Data Per Cycle
- 5,000 to 10,000 points, with a cycle lasting several minutes
- Metrology Approval
- MSA Type 1 and Type 3 procedures
- Sorting
- OK box and NOK chute, with manual review of flagged parts
- Options
- AI surface inspection cameras; eddy current NDT stations for heat-treatment control and crack detection
- Data Interface
- Recipe checked against the plant management system; results and images uploaded to the company information system
Product Description
Dimac SPC-360 is a robotic cell for in-process SPC on complex cold-forged and machined parts. Two sliding drawers hold 36 backlit slots each, and a cobot with a head camera picks parts one at a time in a fixed orientation before a linear axis feeds the main station, where horizontal, upper and diagonal cameras surround an encoder rotary table and a second axis sorts to the OK box or the NOK chute.
Coverage is 6 outer faces plus, on many parts, the inner faces of the broach. Backlit black-and-white images give profile measurements with a standard deviation below 1 micron, including heights referenced to the support plane, while grey-tone images under direct light run at about twice that. MSA Type 1 and Type 3 procedures apply. One cycle runs several minutes and returns 5,000 to 10,000 data points, with up to 50 measurements per part number.
Recipes implement the control plan and are checked against the plant management system before the program starts. Each cycle ends with a summary table flagging every anomaly. Flagged parts go to the NOK chute, where the operator can view the source image, re-run acquisition, key in a measured value or read a USB gauge, with corrections tracked against the operator ID.
Two options extend the scope. AI surface inspection cameras catch small defects, and eddy current stations can sit in the same frame for heat-treatment control and crack detection. The 3 to 20 mm range comes from a delivered job with complex geometry; a part outside that band needs a feasibility check on fixturing, optics and cycle time.
Resources & Documentation
Dimac SPC-360 Robotic SPC Inspection Unit, 4 Cameras, 3-20 mm Cold-Forged Parts
Product Specifications
- Manufacturer
- Dimac Srl
- Model
- SPC-360
- Product Type
- Robotic in-process SPC inspection unit
- Working Range
- Parts from 3 to 20 mm, as delivered on a complex-geometry cold-forging job
- Loading
- Two sliding drawers, 36 backlit slots each
- Handling
- Cobot with head-mounted camera and two linear axes
- Cameras
- Up to 4: cobot head, horizontal, upper and diagonal, plus an encoder rotary table
- Faces Inspected
- Six outer faces and, on many parts, the inner faces of the broach
- Repeatability
- Standard deviation below 1 micron on backlit profile images; about twice that on grey-tone images
- Measurements
- Up to 50 different measurements per part number
- Data Per Cycle
- 5,000 to 10,000 points, with a cycle lasting several minutes
- Metrology Approval
- MSA Type 1 and Type 3 procedures
- Sorting
- OK box and NOK chute, with manual review of flagged parts
- Options
- AI surface inspection cameras; eddy current NDT stations for heat-treatment control and crack detection
- Data Interface
- Recipe checked against the plant management system; results and images uploaded to the company information system

