Product Specifications
- Brand
- Siemens
- Part Number
- 6SL3520-0XC02-2AF0
- Product Type
- Wall-Mounted Distributed Drive
- Series
- SINAMICS G115D
- Rated Power
- 2.2 kW
- Supply Voltage
- 380–480 V 3-Phase
- Rated Output Current
- 5.9 A
- Overload Current
- 11.8 A (200% for 3 s)
- Communication
- PROFINET / EtherNet/IP
- Frame Size
- FSB
- Protection Rating
- IP65 / IP66 / UL Type 4X
Product Description
The Siemens 6SL3520-0XC02-2AF0 is the PROFINET/EtherNet/IP communication variant of the SINAMICS G115D wall-mounted distributed drive family in the 0XC connector configuration, rated at 2.2 kW — the FSA-to-FSB transition power where natural convection in the compact FSA frame becomes insufficient. With 5.9 A rated output (High Overload) and a 380–480 V 3-phase supply, this is the entry-level FSB PROFINET variant: full networked drive functionality — cyclic process data, remote diagnostics, and PROFIsafe SIL 2 safety on a single bus cable — in the larger FSB fanless frame (425 × 180 × 134 mm) that dissipates 2.2 kW of heat without a fan.
Why PROFINET at the FSB entry power?
At 2.2 kW, a conveyor section is typically an accumulation zone, a curve, or a short incline handling enough mechanical load to outgrow the FSA thermal envelope. Integrating these sections into the PROFINET network — rather than running them as isolated hardwired nodes — creates a unified diagnostic environment. The drive appears in TIA Portal alongside every other networked section with identical parameter structure, diagnostic buffer, and conveyor technology function blocks. PROFIsafe SIL 2 safety travels on the same bus cable, eliminating separate safety circuits for the emergency stop loop. The integrated 2-port PROFINET switch enables daisy-chain line topology without additional switches.
What motor types are supported?
The drive delivers 5.9 A rated output current (High Overload) with 200% overload capability — 11.8 A for 3 seconds and 150% for 57 seconds. It supports IE3 three-phase asynchronous motors, IE4 synchronous reluctance motors, and pre-configured SIMOGEAR geared motor combinations up to 2.2 kW. Control modes include V/f, V/f with FCC, and sensorless vector control. Output frequency spans 0–550 Hz in V/f mode and 0–240 Hz in vector mode, with pulse frequency 4 kHz. Integrated 180 V DC brake control.
Frequently Asked Questions
How do I decide between FSA and FSB at 2.2 kW?
At 2.2 kW, natural convection in the FSA frame (380 × 156 × 129 mm) is insufficient — the G115D platform requires the FSB frame (425 × 180 × 134 mm) for thermal management at this power level and above. The question is not a design choice but a physical constraint: if your application genuinely needs 2.2 kW of shaft power at the motor, you are in FSB territory. If your steady-state load is under approximately 1.5 kW, an FSA variant may suffice with correspondingly smaller mechanical dimensions. The 0XC connector and FSB frame are the same physical package across all FSB power ratings.
Can this drive replace an existing FSA PROFINET drive?
Mechanically, the FSB frame is larger than FSA (425 × 180 × 134 mm vs 380 × 156 × 129 mm). If the mounting location has physical clearance for the larger footprint, the electrical and communication interfaces are identical — same PROFINET stack, same PROFIsafe configuration, same TIA Portal integration. The 0XC connector differs from other G115D connector systems — verify that your pre-assembled cable sets match the C-type connector.
Is an external braking resistor required?
The drive includes an integrated brake chopper with a 180 V DC brake control output. For horizontal and moderate-incline conveyor applications, the internal brake management is sufficient. An external braking resistor (minimum 130 Ω for FSB frame) is only needed for high-inertia loads, frequent emergency stops, or decline sections where regenerative energy exceeds the internal chopper's thermal capacity.
Related Products
Resources & Documentation
Siemens 6SL3520-0XC02-2AF0 | SINAMICS G115D Distributed Drive, PROFINET, 2.2 kW, FSB
Product Specifications
- Brand
- Siemens
- Part Number
- 6SL3520-0XC02-2AF0
- Product Type
- Wall-Mounted Distributed Drive
- Series
- SINAMICS G115D
- Rated Power
- 2.2 kW
- Supply Voltage
- 380–480 V 3-Phase
- Rated Output Current
- 5.9 A
- Overload Current
- 11.8 A (200% for 3 s)
- Communication
- PROFINET / EtherNet/IP
- Frame Size
- FSB
- Protection Rating
- IP65 / IP66 / UL Type 4X












